What pinewood derby car design is fastest?

What pinewood derby car design is fastest?
The Black PRO Car is our fastest pinewood derby car. It pushes the Speed Limit! It is track-tested car ready to race featuring our race winning PRO friction-free BSA Ultra-Lite graphite-coated wheels and PRO BSA graphite-coated grooved axles.

Should I bake my pinewood derby block?
Should I bake the pinewood derby block? The short answer is no, do not bake the block. The idea behind baking the block is to remove moisture which will make the block lighter. You can then add more weight to the back of the car.

Is it better to have more weight in front or back of pinewood derby?
PUT MOST OF THE WEIGHT IN THE BACK Science says the heaviest part of your car should be about 1 inch in front of the rear axle. The idea is that the farther back the weight is, the more potential energy you have because your center of mass is higher up on the track.

What is the perfect weight for a pinewood derby car?
The more your pine car weighs, the faster it will go on a downhill ramp. Most rules specify a 5 oz. maximum weight. Most Pinewood Derby cars weigh between 1.5 oz and 3.5 oz (depending on design) without weights so a car may need 3.5 oz or more of additional weight.

Can you glue weights to Pinewood Derby car?
Epoxy can be used for attaching metal accessories to the car and, since it does not shrink when dry, it works well for gluing weight into holes or pockets. It can also be used for gluing wood to wood, but I recommend yellow, white, or tacky glue for that use.

Where is the best place to put weights on a pinewood derby car?
Best Location to Weight Your Pinewood Derby Car When deciding on where to weight your car, you should try to reach a final balance point of the car 1 inch or less in front of the rear axle. To achieve this, place 2/5 of the added weight behind the rear axle, and the remaining 3/5 in front of the rear axle.

Should you sand Pinewood Derby wheels?
The hub can be coned using a lathe, a rotary tool or drill press with a grinder bit, or a special hub tool for pinewood derby wheels. When the plastic has been removed, the hub surface should be sanded first with #220 and then #400 sandpaper and buffed with a plastic polish.

Can a Pinewood Derby car be shorter than 7 inches?
Length and Wheelbase of Pinewood Derby Cars. The length of your Pinewood Derby car is very simple to choose. The rules state a maximum 7-inch length. You want the car to be that long, minus just a little bit (say 1/16″) to allow for judging and measurement slop.

How thin should a Pinewood Derby car be?
1/4″ is thin enough. Most of my cars are 1/4″ in the rear and taper to the front. By making the car much thinner then that, you are putting yourself at risk for the car breaking. It is possible to make them thinner, but it is not really needed.

Do heavier cars corner better?
In theory, a lighter car may handle corners better than a heavy car on a wet roads, as it has less inertia to continue in a straight line, however its lighter weight, there is less friction or adhesion to the road.

Does a heavier pinewood derby car go faster?
Much has been written about the physics of pinewood derby cars, and this is one rare case in racing where heavy = fast. Aerodynamics have little effect in such a short race, but weight does and putting the weight at the back of the car will make your car faster on the flat of the track.

Does a longer wheelbase make a pinewood derby car faster?
The longer the wheel base, the greater the turning distance (a short car turns much more quickly than a long car). A pinewood derby car should go as straight as possible, so a longer wheel base is an advantage.

What is the best way to add weight to a pinewood derby car?
Sand and paint your block but do not add the wheels. When the paint has dried, mount the weight on the top of your car as far to the rear as possible. The weight should not extend past the rear of the car. Glue bottom weights to the bottom of the block to bring the total weight (including wheels and axles) to 5 oz.

What is a good Pinewood Derby time?
Pinewood Derby Results. The average times with just weight added was 3.288 seconds. There was 0.188 seconds between the fastest and slowest car, about 23 inches. The average time was 2.994 seconds, about 44 inches faster than without graphite (0.353 seconds).

Should I glue pinewood derby axles?
7. Create Glue Holes: Glue the axles firmly in their holes to ensure that they stay perfectly placed, but make sure you don’t get glue on your wheels. 8. Add Weight: Remember to make your Pinewood Derby car as heavy as the rules allow.

What is the best type of paint to use on a pinewood derby car?
High-quality, Testors-Model Master acrylic paints are easy to apply, wash up with water, and most importantly, provide a great finish for your pinewood derby car.

Do aerodynamics matter in Pinewood Derby?
A more aerodynamic car (but very similar for other things) doesn’t give you much bang for your buck. Friction will get you. If you can reduce the coefficient of friction by just a little bit, it will make a noticeable difference. If you let your kids do most of the work, they will gain more than a win.

How long do car Derbys last?
Normal heats can last anywhere from 10–30 minutes, while an entire event can take place over the span of a few days. The last running car that makes contact with another driver wins the event.

How much should a Pinewood Derby car weight before paint?
Adding weight. The bottom of a wedge body with holes drilled for weights. Before painting the block, you will want to add enough weight to bring the block, wheels, axles, and any accessories to about 4.9 ounces.

How do you make your RC car faster?
Make it Lighter. Weight is a big deal when it comes to the mobility of RC cars. Consider Changing the Tires. Get Another Pinion Gear. Get Another Battery Pack. Have the Motor Changed. Adjust Motor Timing. Change Bearings. Use Oil Instead of Grease.

Leave a Reply

Your email address will not be published. Required fields are marked *