What are the best materials for a mousetrap car?
A mousetrap car can be made from cardboard or balsa wood with CD’s for wheels and axles of wood or brass tubing. Power to drive the wheels is provided by a mousetrap to which a wand and string is attached to the snap arm.
Are 3 or 4 wheels better for mousetrap cars?
So what is better, three wheels or four wheels? The answer depends on the contest, if we are to build a super fast accelerating speed-trap racer then over coming rotational inertia is one of the main objectives therefor three wheels will always do better than four wheels when it comes to performance.
What kind of string is best for a mousetrap car?
The string has to be strong enough to handle the pulling force but flexible and thin enough to wind tightly around the drive axle. We recommend using a Kevlar based fishing line because its high strength. You should stay away from nylon fishing line and dental floss, these do not work well with mousetrap racers.
What is the best length for a mousetrap car?
Max Length – 45 cm. Max Width – 20 cm. Height – 20 cm. Min ground clearance – 4 cm.
Does a mousetrap car need traction?
Without proper traction your mousetrap racer will loose grip and spin out at the start line wasting energy. Learn how to increase traction and improve acceleration. The maximum acceleration of a mousetrap vehicle depends on the amount of grip or traction the vehicle’s drive wheels have on the road surface.
What is the fastest mousetrap car design?
The Speed-Trap Racer is the fastest mousetrap powered racer anywhere and was designed after Doc Fizzix’s own record-setting mousetrap racer that traveled 5 meters in 1.2 seconds.
Are big wheels better for a mousetrap car?
Wheels and Axles Larger drive wheels will have a greater travel distance per each turn compared to smaller drive wheel. It would make sense to use a super huge drive wheel so for each turn of this massive drive wheel the mousetrap vehicle will travel an incredible distance.
What does the lever arm do in a mousetrap car?
Changing the length of a mouse trap’s snapper (or lever arm) is how you control a mousetrap vehicle’s acceleration and/or travel distance. Different lengths of lever arms can be used to increase and/or decrease the pulling force and change the amount of string that can be pulled off the drive axle.
How long should the lever arm be on a mousetrap car?
For maximum speed, position the mousetrap 2 1/4 inches from the drive axle and cut the lever arm to a length of 4 1/4 inches. The lever arm can be cut using a dremel tool or by using a fine tooth hobby saw. The lever arm should always be “just” long enough to reach the drive axle or performance will be compromised.
What happens if the mousetrap is too far from the drive axle?
6. What happens if the mousetrap is mounted too far from the drive axle? You will lose pulling force or energy to friction.
How do you make a fast mousetrap car?
If you haven’t realized it yet, increasing the length of the lever arm attached to the mousetrap, increases the total mechanical advantage of the car. Therefore, to increase your car’s speed, you can reduce the length of the lever arm attached to the mousetrap.
Should a mousetrap car be heavy or light?
Lighter mousetrap vehicles will require less energy at the start and can use longer lever arms for more pulling distance. Always use lightweight components when building a mousetrap vehicle. bonus tip: lightweight mousetrap vehicles require less pulling force off the start.
Does the length of a mousetrap car matter?
Vehicle weight is an important factor to consider reducing if your mousetrap vehicle is not traveling far enough. The greater your mousetrap vehicle weighs, the shorter the distance it will cover and the speed it will travel. This consequence is due to the limited energy within the mousetrap.
Is wood or cardboard better for mousetrap car?
Balsa wood, pine, or bass wood are excellent choices although balsa wood is somewhat brittle and hard to drill holes into without ripping. Other materials can also be used for making a light weight strong and stiff frame. These include Styrofoam, corrugated cardboard, plastics, aluminum and brass tubing.
How long should dowel be on mousetrap car?
If you have larger drive wheels, these should go on the rear axle and the smaller wheels on the front axle. Your axle dowels should extend past your wheel about 1″ (2.5 cm). around your dowel just outside each of wheels. The elastic band will keep the wheels from falling off of the car.
Why are CDs good for mousetrap cars?
Why do so many mousetrap cars use CD/DVD for wheels? Because CDs and DVDs are some of the best wheels you will ever find for building a long distance mousetrap powered vehicle. CD/DVD wheels can slice through the air with very little air resistance and they have very little rotational inertia.
What is the most important thing to keep in mind when designing a mousetrap car?
Traction is a major issue when it comes to building a super fast speed-trap racer. If there is not enough traction between the drive wheels and the floor then your mousetrap racer will not be able to accelerate as designed. Use drive wheels that provide a lot of traction on the floor.
How is a mousetrap car designs to go straight?
File the back of the front axle hole on the side of the frame opposite the direction the vehicle is turning. bonus tip: Once the axle holes are in alignment the mousetrap vehicle will travel straight.
Is overall weight important in mousetrap cars?
Reduce the most friction you can because the more friction the more energy is lost in propelling the car. Mass should also be taken into account, the more the car weighs the more energy from the mousetrap spring will be used so it’ll be best to make the car light weight.
Can I build my own electric car?
Thankfully, since production of mass-produced electric-car motors, batteries and controllers has increased, getting hold of the components necessary for a home-build has become much easier – now you can even buy DIY electric car conversion kits.