How do you make a Pinewood Derby car super fast?
Bake Your Block. Baking your Pinewood Derby wooden block helps to remove the moisture so that you have more wiggle room to add extra weight at the end. Max Out Your Weight at the Regulation 5 Ounces. Use All of the Graphite. Sand and Polish Your Wheels and Axles. Add Decals.
Does a longer wheelbase make a pinewood derby car faster?
The longer the wheel base, the greater the turning distance (a short car turns much more quickly than a long car). A pinewood derby car should go as straight as possible, so a longer wheel base is an advantage.
What is the perfect weight for a Pinewood Derby car?
MAX OUT YOUR CAR’S WEIGHT AT 5 OZ In most races, a Pinewood Derby car’s weight is limited to 5 ounces. If your car weighs less than that, add coins or other weights.
Do you glue Pinewood Derby axles?
Create Glue Holes: Glue the axles firmly in their holes to ensure that they stay perfectly placed, but make sure you don’t get glue on your wheels. 8. Add Weight: Remember to make your Pinewood Derby car as heavy as the rules allow.
Where should I put the weight on my pinewood derby car?
Best Location to Weight Your Pinewood Derby Car When deciding on where to weight your car, you should try to reach a final balance point of the car 1 inch or less in front of the rear axle. To achieve this, place 2/5 of the added weight behind the rear axle, and the remaining 3/5 in front of the rear axle.
Can a pinewood derby car have 3 wheels?
You may sand the wheels to remove the seam or other imperfections on the surface, but the profile may not be changed (i.e. you can’t make the wheel width thinner). c. Cars can run with 3 wheels touching the track, but the 4th must be installed.
What is a good Pinewood Derby time?
Pinewood Derby Results. The average times with just weight added was 3.288 seconds. There was 0.188 seconds between the fastest and slowest car, about 23 inches. The average time was 2.994 seconds, about 44 inches faster than without graphite (0.353 seconds).
Do aerodynamics matter in Pinewood Derby?
A more aerodynamic car (but very similar for other things) doesn’t give you much bang for your buck. Friction will get you. If you can reduce the coefficient of friction by just a little bit, it will make a noticeable difference. If you let your kids do most of the work, they will gain more than a win.
How far apart should the axles be on a pinewood derby car?
The wheel base (distance from front axle to the rear axle) may not be altered. The cut slots must be used for the axles and the wheel base distance must be 4-1/4 to 4 3/8 inches.
How long does a Pinewood Derby last?
A regular Pinewood Derby race on a 40-foot track lasts a couple of seconds. The Pinewood Derby Race Across America is expected to last about 12 days.
What Pinewood Derby car design is fastest?
The Black PRO Car is our fastest pinewood derby car. It pushes the Speed Limit! It is track-tested car ready to race featuring our race winning PRO friction-free BSA Ultra-Lite graphite-coated wheels and PRO BSA graphite-coated grooved axles.
Should a pinewood derby car be light or heavy?
8. Add Weight: Remember to make your Pinewood Derby car as heavy as the rules allow. In general, it’s best to place weight to the rear of your car because a heavier rear increases speed.
Should I bake my Pinewood Derby block?
Should I bake the pinewood derby block? The short answer is no, do not bake the block. The idea behind baking the block is to remove moisture which will make the block lighter. You can then add more weight to the back of the car.
Do heavier pinewood derby cars go faster?
Much has been written about the physics of pinewood derby cars, and this is one rare case in racing where heavy = fast. Aerodynamics have little effect in such a short race, but weight does and putting the weight at the back of the car will make your car faster on the flat of the track.
Can a pinewood derby car be too heavy?
Assuming all other factors are equal, a heavier car will be faster than a lighter car. The Pinewood Derby rules limit the weight of each car to 5 ounces.
How thin should a pinewood derby car be?
1/4″ is thin enough. Most of my cars are 1/4″ in the rear and taper to the front. By making the car much thinner then that, you are putting yourself at risk for the car breaking. It is possible to make them thinner, but it is not really needed.
What is the best length for a Pinewood Derby car?
Length and Wheelbase of Pinewood Derby Cars. The length of your Pinewood Derby car is very simple to choose. The rules state a maximum 7-inch length. You want the car to be that long, minus just a little bit (say 1/16″) to allow for judging and measurement slop.
What kind of paint is best for pinewood derby cars?
High-quality, Testors-Model Master acrylic paints are easy to apply, wash up with water, and most importantly, provide a great finish for your pinewood derby car.
Should you sand Pinewood Derby wheels?
The hub can be coned using a lathe, a rotary tool or drill press with a grinder bit, or a special hub tool for pinewood derby wheels. When the plastic has been removed, the hub surface should be sanded first with #220 and then #400 sandpaper and buffed with a plastic polish.
What’s the best shape for a Pinewood Derby car?
But aerodynamics rule the day, and the best shape is a simple wedge. Just like a spoiler on the rear of a sports car, the wedge shape allows as much air to flow over the top of the car without hinderance while keeping the car pinned to the track.