How do you make a mousetrap car go super far?
lever arm length If you haven’t realized it yet, increasing the length of the lever arm attached to the mousetrap, increases the total mechanical advantage of the car. Therefore, to increase your car’s speed, you can reduce the length of the lever arm attached to the mousetrap.
Are big wheels better for a mousetrap car?
Wheels and Axles Larger drive wheels will have a greater travel distance per each turn compared to smaller drive wheel. It would make sense to use a super huge drive wheel so for each turn of this massive drive wheel the mousetrap vehicle will travel an incredible distance.
What is the fastest mousetrap car design?
The Speed-Trap Racer is the fastest mousetrap powered racer anywhere and was designed after Doc Fizzix’s own record-setting mousetrap racer that traveled 5 meters in 1.2 seconds.
What is the best amount of wheels for a mousetrap car?
So what is better, three wheels or four wheels? The answer depends on the contest, if we are to build a super fast accelerating speed-trap racer then over coming rotational inertia is one of the main objectives therefor three wheels will always do better than four wheels when it comes to performance.
What is the best wood for a mousetrap car?
Balsa wood, pine, or bass wood are excellent choices although balsa wood is somewhat brittle and hard to drill holes into without ripping. Other materials can also be used for making a light weight strong and stiff frame. These include Styrofoam, corrugated cardboard, plastics, aluminum and brass tubing.
Is overall weight important in mousetrap cars?
Reduce the most friction you can because the more friction the more energy is lost in propelling the car. Mass should also be taken into account, the more the car weighs the more energy from the mousetrap spring will be used so it’ll be best to make the car light weight.
Can a mouse be too light for a trap?
Like rats, mice can also eat lure from many rat traps without triggering them as often they’re too light to trigger the trap.
How long should dowel be on mousetrap car?
If you have larger drive wheels, these should go on the rear axle and the smaller wheels on the front axle. Your axle dowels should extend past your wheel about 1″ (2.5 cm). around your dowel just outside each of wheels. The elastic band will keep the wheels from falling off of the car.
How do you reduce friction on a mousetrap car?
Try to have a minimum gap of 1/8 inch between the frame and any spacers (or wheels) in order to decrease any rubbing friction. Use thrust washers and graphite powder between spacers (or wheels) and the frame to help reduce the rubbing friction.
What is the basic design of a mousetrap car?
The most basic design for propelling a mousetrap racers is to tie one end of a string to a mouse trap’s snapper arm and then attach the other end of the string to a drive axle. By turning the drive axle the string is wound around the drive axle causing the mouse trap’s spring to compress and store energy.
Should a mousetrap car be heavy or light?
Lighter mousetrap vehicles will require less energy at the start and can use longer lever arms for more pulling distance. Always use lightweight components when building a mousetrap vehicle. bonus tip: lightweight mousetrap vehicles require less pulling force off the start.
What kind of string is best for a mousetrap car?
The string has to be strong enough to handle the pulling force but flexible and thin enough to wind tightly around the drive axle. We recommend using a Kevlar based fishing line because its high strength. You should stay away from nylon fishing line and dental floss, these do not work well with mousetrap racers.
What is the best length for a mousetrap car?
Max Length – 45 cm. Max Width – 20 cm. Height – 20 cm. Min ground clearance – 4 cm.
Does the length of a mousetrap car matter?
Vehicle weight is an important factor to consider reducing if your mousetrap vehicle is not traveling far enough. The greater your mousetrap vehicle weighs, the shorter the distance it will cover and the speed it will travel. This consequence is due to the limited energy within the mousetrap.
What makes a mousetrap car move?
The mousetrap storespotential energyin the form of the spring. That potential energy is converted into kinetic energy in the form of the arm rotating forward. The arm pulls on the wound-up string, which turns the drive wheel dowel, which is connected to the wheels, which makes the car drive forward.
Why is my mousetrap car not going straight?
If a mousetrap vehicle is not traveling straight then there is one reason and one reason only: the front and rear axles are not parallel to one another!
How do you adjust the pulling force of the mousetrap?
Changing the length of the mouse trap’s lever arm controls the pulling force and the amount of string that can be wound around the drive axle. Making the length of the mouse trap’s lever arm longer will decrease the pulling force but increase the amount of string that can be pulling from the drive axle.
How do you make a mousetrap car go forward and backwards?
To make a reversing mousetrap car go forward and then come back you will need to know how to “back-wind” the string. Back-winding the string it a technique where you first wind the string around the axle in one direction and then rewind the string in the opposite direction.
What does the lever arm do in a mousetrap car?
Changing the length of a mouse trap’s snapper (or lever arm) is how you control a mousetrap vehicle’s acceleration and/or travel distance. Different lengths of lever arms can be used to increase and/or decrease the pulling force and change the amount of string that can be pulled off the drive axle.
How do you make an awesome pinewood derby car?
Bake your block. Max out your weight at the regulation 5 ounces. Use all of the graphite. Sand and polish your wheels and axles. Check alignment. Spend time sanding. Use a high-quality paint. Add decals.