How can I make my pinewood derby car better?
Put all of your weight in the back. Lube the car at the body/wheel friction point. Spend a fair amount of time on axle prep. Make sure your wheels are ready. Finally, once your wheels are mounted, check their alignment.
Is it better to have more weight in front or back of pinewood derby?
PUT MOST OF THE WEIGHT IN THE BACK Science says the heaviest part of your car should be about 1 inch in front of the rear axle. The idea is that the farther back the weight is, the more potential energy you have because your center of mass is higher up on the track.
Does a longer wheelbase make a pinewood derby car faster?
The longer the wheel base, the greater the turning distance (a short car turns much more quickly than a long car). A pinewood derby car should go as straight as possible, so a longer wheel base is an advantage.
Does graphite help pinewood derby car?
Powdered graphite is an excellent lubricant to reduce friction on pinewood derby axles. Why do you want to reduce friction on your axles? It’s simple physics; reduce friction to make your car faster. Stated another way, the fastest cars have the least friction.
Do you glue pinewood derby axles?
Create Glue Holes: Glue the axles firmly in their holes to ensure that they stay perfectly placed, but make sure you don’t get glue on your wheels. 8. Add Weight: Remember to make your Pinewood Derby car as heavy as the rules allow.
Can a pinewood derby car be too heavy?
Assuming all other factors are equal, a heavier car will be faster than a lighter car. The Pinewood Derby rules limit the weight of each car to 5 ounces.
Can a pinewood derby car have 3 wheels?
You may sand the wheels to remove the seam or other imperfections on the surface, but the profile may not be changed (i.e. you can’t make the wheel width thinner). c. Cars can run with 3 wheels touching the track, but the 4th must be installed.
Can a pinewood derby car be shorter than 7 inches?
Length and Wheelbase of Pinewood Derby Cars. The length of your Pinewood Derby car is very simple to choose. The rules state a maximum 7-inch length. You want the car to be that long, minus just a little bit (say 1/16″) to allow for judging and measurement slop.
How do you seal a pinewood derby car?
Apply two coats of liquid sanding sealer. Let the sealer dry overnight before sanding it lightly with fine-grit paper. If the grain still shows, apply two more coats of sealer. Let it dry overnight and sand again.
What do you spray graphite with?
Winsor & Newton Artists’ Fixative This workable fixative is an excellent choice for artists who work in graphite, pastel, pencil, and chalk. It offers great smudge and dust protection after you spray over a layer, drying quite rapidly so you can lay down the next layer.
Where is the best place to put weight on a pinewood derby car?
Best Location to Weight Your Pinewood Derby Car When deciding on where to weight your car, you should try to reach a final balance point of the car 1 inch or less in front of the rear axle. To achieve this, place 2/5 of the added weight behind the rear axle, and the remaining 3/5 in front of the rear axle.
Should I bake my pinewood derby block?
Should I bake the pinewood derby block? The short answer is no, do not bake the block. The idea behind baking the block is to remove moisture which will make the block lighter. You can then add more weight to the back of the car.
What kind of paint is best for pinewood derby cars?
High-quality, Testors-Model Master acrylic paints are easy to apply, wash up with water, and most importantly, provide a great finish for your pinewood derby car.
What is a good pinewood derby time?
Pinewood Derby Results. The average times with just weight added was 3.288 seconds. There was 0.188 seconds between the fastest and slowest car, about 23 inches. The average time was 2.994 seconds, about 44 inches faster than without graphite (0.353 seconds).
Do heavier cars corner better?
In theory, a lighter car may handle corners better than a heavy car on a wet roads, as it has less inertia to continue in a straight line, however its lighter weight, there is less friction or adhesion to the road.
Do aerodynamics matter in pinewood derby?
A more aerodynamic car (but very similar for other things) doesn’t give you much bang for your buck. Friction will get you. If you can reduce the coefficient of friction by just a little bit, it will make a noticeable difference. If you let your kids do most of the work, they will gain more than a win.
Should you sand Pinewood Derby wheels?
The hub can be coned using a lathe, a rotary tool or drill press with a grinder bit, or a special hub tool for pinewood derby wheels. When the plastic has been removed, the hub surface should be sanded first with #220 and then #400 sandpaper and buffed with a plastic polish.
How do you reduce drag on a derby car?
Taper the Bottom of Your Car at the Front – This will keep it from rubbing against the track at the bottom of the slope as the track becomes flat. Lift One of the Front Wheels, so it Doesn’t Touch the Track – If your competition allows it, raising one wheel is an easy way to reduce friction.
What is the best weight for pinewood derby?
The more your pine car weighs, the faster it will go on a downhill ramp. Most rules specify a 5 oz. maximum weight. Most Pinewood Derby cars weigh between 1.5 oz and 3.5 oz (depending on design) without weights so a car may need 3.5 oz or more of additional weight.
What are the best materials to make a mousetrap car?
A mousetrap car can be made from cardboard or balsa wood with CD’s for wheels and axles of wood or brass tubing. Power to drive the wheels is provided by a mousetrap to which a wand and string is attached to the snap arm.